View TLP705_1139017.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

TLP705
Preliminary
TOSHIBA Photocoupler GaAAs IRED + Photo IC
TLP705
Plasma Display Panel. Industrial Inverter IGBT/Power MOS FET Gate Drive
The TOSHIBA TLP705 consists of a GaAAs light emitting diode and a integrated photodetector. This unit is 6-lead SDIP package. TLP705 is 50% smaller than 8PIN DIP and has suited the safety standard reinforced insulation class. So mounting area in safety standard required equipment can be reduced. TLP705 is suitable for gate driving circuit of IGBT or power MOS FET. Especially TLP705 is capable of "direct" gate drive of lowr Power IGBTs. Unit in mm
4.580.25
65 4
3.65 -0.25
+0.15
6.80.25
12
3
7.620.25 0.25
* * * * * * * * * * *
1.270.2
1.250.25 10.0max
11-5J1
Peak output current Operating frequency Supply current Power supply voltage Threshold input current Switching time (tpLH / tpHL) Common mode transient immunity Isolation voltage UL Recognized Construction Mechanical Rating
7.62 mm pich standard type Creepage Distance Clearance Insulation Thickness 7.0 mm (Min) 7.0 mm (Min) 0.4 mm (Min)
: 0.45 A (max) : 250kHz (max) : 3mA (max) : 10 to 20 V : IFLH = 8 mA (max) : 200 ns (max) : 10 kV/s : 5000 Vrms :UL1577, File No.E67349
10.16 mm pich TLPXXXF type 8.0 mm (Min) 8.0 mm (Min) 0.4 mm (Min)
0.40.1
Guaranteed performance over temperature : -40 to 100C TOSHIBA Weight 11-5J1 0.26 g (t y p .)
Truth Table
Input H L LED ON OFF Tr1 ON OFF Tr2 OFF ON Output H L
Pin Configuration (top view)
Schematic
(Tr1) ICC 6 VCC
1 2 3
SHIELD
6 5 4
1: Anode 2: NC 3: Cathode 4: GND 5: VO (output) 6: VCC
IF 1+ VF 3- (Tr2) IO 5 VO 4 GND
SHIELD A 0.1 F bypass capacitor must be connected between pin 6 and 4. (See Note 6)
1
2004-10-19
4.0 -0.20
+0.25
TLP705
Maximum Ratings (Ta = 25C)
Characteristics Forward current Forward current derating (Ta 85C) LED Peak transient forward current Reverse voltage Junction temperature "H" peak output current Detector "L" peak output current Output voltage Supply voltage Junction temperature Operating frequency Storage temperature range Operating temperature range Lead soldering temperature (10 s) Isolation voltage (AC, 1 minute, R.H. 60%) (Note 4) (Note 5) (Note 3) (Note 2) (Note 2) (Note 1) Symbol IF IF/Ta IFP VR Tj IOPH IOPL VO VCC Tj f Tstg Topr Tsol BVS Rating 20 -0.54 1 5 125 -0.45 0.45 25 25 125 250 -55 to 125 -40 to 100 260 5000 Unit mA mA/C A V C A A V V C kHz C C C Vr m s
Note 1: Pulse width PW 1s, 300 pps Note 2: Exponential waveform pulse width PW 10 s , f 15 kHz Note 3: Exponential waveform IOPH -0.25 A (80 ns) , IOPL +0.25 A (80 ns) ,Ta =100 C Note 4: It is effective soldering area of Lead . Note 5: Device considerd a two terminal device: pins 1, 2 and 3 shorted together, and pins 4, 5 and 6 shorted together. Note 6: A ceramic capacitor(0.1 F) should be connected from pin 6 to pin 4 to stabilize the operation of the high gain linear amplifier. Failure to provide the bypassing may impair the switching property. The total lead length between capacitor and coupler should not exceed 1 cm.
Recommended Operating Conditions
Characteristics Input current, ON Input voltage, OFF Supply voltage Peak output current Operating temperature (Note 7) Symbol IF (ON) VF (OFF) VCC IOPH / IOPL Topr Min 10 0 10 Typ. Max 15 0.8 20 0.15 100 Unit mA V V A C
- 40
Note 7: Input signal rise time (fall time) < 0.5 s.
2
2004-10-19
TLP705
Electrical Characteristics (Ta = -40 to 100C, unless otherwise specified)
Characteristics Forward voltage Temperature coefficient of forward voltage Input reverse current Input capacitance "H" Level (Note 8) Symbol VF VF/Ta IR CT IOPH1 IOPH2 IOPL1 IOPL2 VOH VOL ICCH ICCL IFLH VFHL VCC Test Circu it 1 Test Condition IF = 10 mA, Ta = 25C IF = 10 mA VR = 5 V, Ta = 25C V = 0 V , f = 1 MHz,Ta = 25C VCC = 15 V IF = 10 mA VCC = 15 V IF = 0 mA V6-5 = 4 V V6-5 = 10 V V5-4 = 2 V V5-4 = 10 V IO = -100 mA, IF = 10 mA IO = 100 mA, VF = 0.8 V Min -0.15 -0.3 0.15 0.3 6.0 0.8 10 Typ.* 1.6 -2.0 45 -0.35 -0.6 0.36 0.62 8.5 0.4 2.0 2.0 2.5 Max 1.8 10 V 1.0 3.0 3.0 8 20 mA mA V V A Unit V mV/C A pF
Output current
"L" Level "H" Level
2 3
Output voltage "L" Level Supply current Threshold input current Threshold input voltage Supply voltage "H" Level "L" Level LH HL 4 5 6
VCC = 10 V
VCC = 10 to 20 V IF = 10 mA VO open IF = 0 mA VCC = 15 V, VO > 1 V VCC = 15 V, VO < 1 V
*: All typical values are at Ta = 25C Note 8: Duration of IO time 50 s Note 9: This product is more sensitive than the conventional product to static electricity (ESD) because of a lowest power consumption design. General precaution to static electricity (ESD) is necessary for handling this component.
Isolation Characteristics (Ta = 25C)
Characteristic Capacitance input to output Isolation resistance Symbol CS RS Test Condition V = 0 V, f = 1MHz R.H. 60%,VS = 500V AC, 1 minute Isolation voltage BVS AC, 1 second, in oil DC,1 minute,in oil (Note 5) (Note 5) Min. 1x10
12
Typ. 1.0 10
14
Max.
Unit pF Vrms Vdc
5000
10000 10000
3
2004-10-19
TLP705
Switching Characteristics (Ta = -40 to 100C, unless otherwise specified)
Characteristics LH Propagation delay time HL LH Propagation delay time HL Propagation delay difference between any two parts or channels Pulse Width Distortion Output rise time (10-90%) Output fall time (90-10%) Common mode transient immunity at hight level output Common mode transient immunity at low level output tpHL 7 tpsk PWD (tpHL-tpLH) tr tf CMH 8 CML VCM = 1000Vp-p VCC = 20 V Ta = 25C tpHL tpLH VCC = 20 V Rg = 30 Cg = 1 nF f=250kHz Duty Cycle =50% Symbol tpLH Test Circuit Test Condition Ta= 25 IF = 0 10 mA Ta= 25 IF = 10 0 mA Ta= -40 to100 IF = 0 10 mA Ta= -40 to100 IF = 10 0 mA Ta= -40 to100 IF = 10 mA Ta= -40 to100 IF = 10 mA IF = 0 10 mA IF = 10 0 mA IF = 10 mA VO (min) = 16 V IF = 0 mA VO (max) = 1 V Min 70 70 50 50 -90 Typ.* 95 105 Max 170 170 200 200 ns 90 Unit
-65 -10000 10000

65 V/s
*: All typical values are at Ta = 25C
Test Circuit 1: IOPH
1 6 V6-5 IF A IOPH VCC 3 4
Test Circuit 2: IOPL
1 6 IOPL A VCC 3 V5-4 4
Test Circuit 3: VOH
1 6 VOH V IF VCC 3 4 VF
Test Circuit 4: VOL
1 6 VOL V 3 4 VCC
4
2004-10-19
TLP705
Test Circuit 5: ICCH
1 6
ICCH A
1
Test Circuit 6: ICCL
6
ICCL A VCC
IF VCC 3 4 3 4
Test Circuit 7 : tpLH, tpHL, tr, tf, PWD
0.1 F
IF ( f=250 kHz , Duty=50 %)
1
6 VO Rg = 30 Cg = 1 nF IF VCC VO tpLH tpHL tr tf VOH 90% 50 10% VOL
3
4
Test Circuit 8: CMH, CML
IF SW A 1 6 VCM B 0.1 F VO VCC * SW A: IF = 10 mA 3 VCM + - 4 VO 1V * SW B: IF = 0 mA CML = 800 V tr (s) 16V CML CMH 90% 10% tr tf 1000 V
CMH =- 800 V tf (s)
CML (CMH) is the maximum rate of rise (fall) of the common mode voltage that can be sustained with the output voltage in the low (high) state.
5
2004-10-19
TLP705
RESTRICTIONS ON PRODUCT USE
* The information contained herein is subject to change without notice.
030619EBC
* The information contained herein is presented only as a guide for the applications of our products. No responsibility is assumed by TOSHIBA for any infringements of patents or other rights of the third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of TOSHIBA or others. * TOSHIBA is continually working to improve the quality and reliability of its products. Nevertheless, semiconductor devices in general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical stress. It is the responsibility of the buyer, when utilizing TOSHIBA products, to comply with the standards of safety in making a safe design for the entire system, and to avoid situations in which a malfunction or failure of such TOSHIBA products could cause loss of human life, bodily injury or damage to property. In developing your designs, please ensure that TOSHIBA products are used within specified operating ranges as set forth in the most recent TOSHIBA products specifications. Also, please keep in mind the precautions and conditions set forth in the "Handling Guide for Semiconductor Devices," or "TOSHIBA Semiconductor Reliability Handbook" etc.. * The TOSHIBA products listed in this document are intended for usage in general electronics applications (computer, personal equipment, office equipment, measuring equipment, industrial robotics, domestic appliances, etc.). These TOSHIBA products are neither intended nor warranted for usage in equipment that requires extraordinarily high quality and/or reliability or a malfunction or failure of which may cause loss of human life or bodily injury ("Unintended Usage"). Unintended Usage include atomic energy control instruments, airplane or spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments, medical instruments, all types of safety devices, etc.. Unintended Usage of TOSHIBA products listed in this document shall be made at the customer's own risk. * The products described in this document are subject to the foreign exchange and foreign trade laws. * TOSHIBA products should not be embedded to the downstream products which are prohibited to be produced and sold, under any law and regulations. * GaAs(Gallium Arsenide) is used in this product. The dust or vapor is harmful to the human body. Do not break, cut, crush or dissolve chemically.
6
2004-10-19

▲Up To Search▲

Price & Availability of TLP705

	To Download TLP705 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .